whatsapp logo
Dyno Project

Jetour T2 ECU Remap - Power Upgrade (+21 HP / +31 Nm)

Published Updated
Jetour T2 ECU Remap - Power Upgrade (+21 HP / +31 Nm)

Jetour T2 2025 2.0T, Stage1 ECU Remap: +21 WHP / +31 Nm (DynoJet-Verified)

CaracalTech Stage 1 ECU remap for the Jetour T2 2.0T (Chery SQRF4J20, 7-speed DCT) adds +21 WHP and +31 Nm at the wheels (about 10% power increase).

  • Measured on our in-house DynoJet dynamometer.
  • The DCT torque limits are fully respected; the ECU and TCU remain synchronized.
  • The file is 100% reversible, with a lifetime software warranty and money-back guarantee.
  • Remote calibration with data-log revisions, typically within 1~2 hours.

Engine & Factory Output

The Jetour T2 2025 runs the SQRF4J20, a 2.0-litre turbocharged petrol engine from Chery Automobile. This engine is shared across several Chery group platforms, including the Tiggo 8 & 9 Pro Max, Exeed TXL, Exeed VX, and Jaecoo J8 models. In the T2, it is factory-rated at 245 HP and 375 Nm.

Key Specifications (Factory):

SpecificationValue
Engine CodeSQRF4J20
Displacement1998 cc
Max Power (Factory)245 HP
Max Torque (Factory)375 Nm
Transmission7-speed DCT
Compression Ratio10.2:1
Weight1980 kg
Fuel Tank70 L
ECUBosch MG1US008

The Jetour T2 is also sold as the Jetour Traveller and Jetour Shanhai T2 in some markets. Regardless of the badge, the hardware and calibration architecture are identical.

The torque curve is wide, but the 10.2:1 compression ratio is high for a turbo engine. This affects how much ignition advance can be added safely. The 7-speed DCT also has its own torque limits, so the ECU and TCU must stay synchronized.

Because the DCT monitors torque requests, we adjust the engine torque model so the gearbox does not see values that trigger clutch slip or protection. This is different from a simple "more boost" file.

Stage 1 Calibration Strategy for the SQRF4J20

Stage 1 is a software-only calibration. No hardware is changed. On this engine, we focus on four key areas:

AFR tuning for best performance: We optimize the air-fuel ratio across the rev range to improve combustion efficiency and power delivery. The target AFR is calibrated for the engine's specific load and RPM conditions.

Ignition timing under high compression: The 10.2:1 compression ratio requires careful ignition advance. We advance timing within the knock threshold, using the factory knock sensor feedback to validate safety.

Turbo boost control to increase torque: We increase boost pressure within the turbocharger's efficiency range, prioritizing low-to-mid RPM response rather than chasing peak numbers.

Throttle mapping: We reduce electronic throttle lag for sharper pedal response.

Cooling system calibration for tropical climates: Because the SQRF4J20 is turbocharged, we adjust cooling system parameters to reduce operating temperatures in hot climates, protecting the engine under sustained high-load conditions.

Conservative ignition advance: We carefully select ignition advance changes to prevent knock, especially in high ambient temperatures and with varying fuel quality.

Dyno-Verified Stage 1 Results

Our in-house DynoJet testing on the Jetour T2 2025 2.0T produced the following results at the wheels:

 

Jetur T2 Dyno Results caracaltech
VersionPower (WHP)Torque (Nm)
Stock205350
Stage 1226381
Stage 2 (Downpipe + Exhaust)237390

Stage 1 gain: +21 WHP and +31 Nm at the wheels. That is about a 10% power increase. The torque gain is strongest in the low-to-mid range, which is where the T2 needs it most.

Stage 2 (Optional)
For customers seeking more, Stage 2 adds a downpipe and performance exhaust. This further reduces backpressure and allows a more aggressive calibration. Stage 2 delivers +32 WHP and +40 Nm over stock. It is recommended for off-road or track use only and requires supporting hardware.

How It Feels on the Road

The extra torque changes the T2's character:

Less turbo lag when pulling away

Quicker downshifts because the DCT sees stronger torque

Easier overtaking on the highway

Better low-speed control off-road

More confident towing (more torque in low RPM)

The car does not feel like a different vehicle. It feels like the factory restriction has been removed.

Remote Calibration Process for Jetour T2

Step 1: Read the ECU
Use Kess3, DimSport, PCM Flash, or MagicMotorSport. OBD or bench mode depends on your tool and module. For the Bosch MG1US008, bench mode is recommended for reliable reading.

 ProgrammerReading Process
1KESS 3Bench mode / Jtag
2Dim SportBench Mode
3Magic Motor SportOBD
4PCM FlashOBD / Bench mode
5CombiloaderOBD / Bench mode

Step 2: Send the file
Upload the original file. We identify the calibration, check the software version, and build a custom file.

Step 3: Write the tuned file
We return the file within 1~2 hours. Writing takes under 10 minutes.

Step 4: Data logging and revisions
Drive for about 35 minutes. Log boost, RPM, coolant temperature, and DCT torque. Send logs. We refine if needed. Usually 1~2 revisions.

Safety and DCT Considerations

The Stage 1 file stays within factory safety margins. We keep a backup. It is 100% reversible. The DCT torque limits are respected. If writing is interrupted, professional tools have recovery modes. Every file is dyno-tested on our in-house DynoJet before delivery.

FAQ

How much gain does Stage 1 provide on the Jetour T2?
Stage 1 on the Jetour T2 2.0T provides about +21 WHP and +31 Nm at the wheels, measured on our in-house DynoJet.

Is the remap reversible?
Yes, 100%. CaracalTech keeps a backup of your original ECU file and can restore it at any time, for example before a dealer visit.

How long does the remote calibration process take?
The main process (reading, sending, writing) takes about 1~2 hours. Revisions, if needed, are completed within 1~2 days.

Will fuel consumption increase after the remap?
In many cases, fuel efficiency improves because the engine works more efficiently. Driving style remains the biggest factor.

What tools do I need for the Jetour T2 remap?
You need Kess3, DimSport, PCM Flash, or MagicMotorSport, a Windows laptop, and a stable internet connection. Bench mode is recommended for the Bosch MG1US008.

Does this void the manufacturer's warranty?
The process is reversible. You can restore the original file before visiting a dealer for warranty service.

Who is this for?
This Stage 1 remap is ideal for T2 owners who want more low-end torque for daily driving, off-road use, or towing. It is not recommended for vehicles with existing DCT clutch wear or those using low-octane fuel without supporting modifications.

Why Choose CaracalTech?

  • Expert calibrators with experience on Chery group engines
  • Remote service, no workshop visit required.
  • Custom files, not generic maps
  • Revisions included
  • Dyno-verified on our in-house DynoJet
  • Safe and reversible
  • Lifetime software warranty
  • Money-back guarantee
  • Free technical support

Ready to Unlock Your Jetour T2?

Request a free quote. Book your remap. Free consultation.

Don't let your Jetour T2 run below its potential. Unlock the extra 21 WHP and 31 Nm today.

Author: CaracalTech Calibration Team
Last Updated: September 2026
 

Keywords:bosch mg1us008-jetour shanhai t2-jetour t2 2.0t ecu remap-jetour t2 dyno tuning-jetour t2 stage 1 tuning-jetour traveller-sqrf4j20 chip tuning

Enjoyed the content? Add us as a preferred source to see more of it in Search.

Add as a preferred source on Google
Your Rating
Rate: 5.00 (1)
Community
Comments: