whatsapp logo
Dyno Project

Tank 300 2.0T Stage 1 & Stage 2 ECU Remap +26 WHP / +26 Nm (DynoJet-Verified)

Published Updated
Tank 300 2.0T Stage 1 & Stage 2 ECU Remap +26 WHP / +26 Nm (DynoJet-Verified)

Tank 300 2.0T Stage 1 & Stage 2 ECU Remap, +45 WHP / +32 Nm (DynoJet-Verified)

Key Takeaways

  • CaracalTech Stage 1 ECU remap for the Tank 300 2.0T (GW E20CB, ZF 8HP) adds +26 WHP and +26 Nm at the wheels.
  • Stage 2 (Downpipe + Intake Kit) pushes further to +45 WHP and +32 Nm over stock.
  • Measured on our in-house DynoJet dynamometer in Dubai.
  • The ZF 8HP50 transmission shift logic is recalibrated to reduce the factory hesitation.
  • Cooling system parameters are adjusted to lower operating temperatures in hot climates.
  • The file is 100% reversible, with a lifetime software warranty and money-back guarantee.
  • Remote calibration with data-log revisions, typically within 1~2 hours.

Engine & Factory Output

The Tank 300 is powered by the E20CB, a 2.0-litre turbocharged petrol engine from Great Wall Motors (GWM). This engine is part of the GW4C20 family and shares its core architecture with engines used in the Haval H9, Wey VV6, and Haval F7x. In the Tank 300, it is factory-rated at 225 HP and 387 Nm.

Key Specifications:

Specification

Value

Engine Code

E20CB

Displacement

1978 cc

Max Power (Factory)

225 HP @ 5500 RPM

Max Torque (Factory)

387 Nm @ 1800–3900 RPM

Transmission

8-speed AT (ZF 8HP50)

Drivetrain

4WD

Compression Ratio

9.6:1

Weight

2155 kg

Fuel Tank Capacity

75 L

ECU

Bosch MG1US008

Fuel Requirement

95 RON minimum

The Tank 300 is also sold as the Wey Tank 300 in some markets. Regardless of the badge, the hardware and calibration architecture are identical.

Stage 1 Calibration Strategy for the Tank300 with E20CB engine

Stage 1 is a software-only modification. No hardware changes are required. On this engine, we focus on five key areas:

Torque management for the ZF 8HP50: The 8HP50 gearbox has specific torque limits. We recalibrate the engine torque model to stay within safe transmission parameters while maximizing usable output. The factory shift logic also exhibits a noticeable hesitation when pulling away from a stop; we refine the torque request strategy to sharpen this response.

Ignition timing under 9.6:1 compression: This compression ratio is moderate for a turbocharged engine. We advance timing carefully within the knock threshold, using factory knock sensor feedback to validate safety.

Turbo boost pressure: We increase boost within the turbocharger’s efficiency range, focusing on low-to-mid RPM response. The factory calibration reduces boost significantly above 3700 RPM, which causes the power to drop off sharply. Our calibration smooths this curve and extends the usable powerband.

Throttle mapping: We reduce electronic throttle lag for sharper pedal response.

Cooling system calibration for hot climates: We adjust cooling system parameters to reduce operating temperatures, protecting the engine and turbocharger under sustained high-load conditions. This is particularly important for a heavy 4WD vehicle in tropical and desert climates.

All adjustments stay within factory safety margins. The original file is always backed up.

Thermal and Mechanical Considerations for Hot Climates

The  E20CB engine is a direct-injection turbocharged engine with documented sensitivity to thermal load. In hot climates, several factors require attention before calibration:

  • Cooling system under heavy load: The Tank 300 weighs 2155 kg, and the factory cooling system has limited reserve. Owners in warm regions have reported overheating in city traffic and during towing, especially with the air conditioning running. Our calibration adjusts cooling system parameters to reduce operating temperatures under sustained load.
  • Turbocharger heat management: The turbocharger is sensitive to heat soak, particularly in stop-and-go traffic after hard driving. Our calibration includes thermal management strategies that reduce peak turbo temperatures.
  • Timing chain integrity: This engine family has documented cases of timing chain stretch, often linked to extended oil change intervals and high engine loads. We inspect the timing system before any remap. Oil change intervals of 7,000~8,000 km are strongly recommended for tuned vehicles.
  • Intake valve carbon deposits: GDI engines accumulate carbon on intake valves, which increases knock tendency. A walnut blasting service is recommended if deposits are suspected.
  • Fuel quality sensitivity: The E20CB requires 95 RON minimum. In regions with lower-octane fuel, we adjust the calibration to operate safely within the available fuel’s knock resistance.

Case Study: Dyno-Verified Stage 1 & Stage 2 Results

Our in-house DynoJet testing on the Tank 300 2.0T produced the following results at the wheels:

Tank 300 2.0T Stage 1 & Stage 2 ECU Remap +26 WHP / +26 Nm (DynoJet-Verified)

 

VersionPower (WHP)Torque (Nm)
Stock (Run 0)178 WHP @ 5500 RPM363 Nm @ 1800–3900 RPM
Stage 1 (Run 1)198 WHP @ 5500 RPM375 Nm @ 1900–4000 RPM
Stage 2 (Downpipe + Intake Kit, Run 2)223 WHP @ 5400 RPM395 Nm @ 1950–4000 RPM

Stage 1 delivers +20 WHP and +12 Nm at the wheels. Stage 2 pushes further to +39 WHP and +46 Nm over stock.

Test Conditions: In-house DynoJet dynamometer, ambient temperature 35–40 °C, 95 RON fuel, vehicle mileage approximately 13,000 km, Dubai.

Important Note on Data Interpretation: You may see different gain figures for the Tank 300 2.0T on international tuning forums. For example, MasterTuning (Europe) reports Stage 1 gains of +21 HP and +33 Nm, while IM Chip (Russia) claims gains of approximately +50 HP and +120 Nm. These differences come from three factors: different testing standards (wheel vs. engine output), different tuning aggressiveness (safety margin vs. maximum output), and different factory calibration versions. Our calibration strategy prioritizes reliability and daily drivability, delivering verified, repeatable gains within safe margins.

How It Feels on the Road

The extra torque transforms the Tank 300’s character:

Sharper throttle response, The electronic lag between pedal and engine is significantly reduced.

Reduced transmission hesitation, The factory pause when pulling away from a stop is noticeably diminished. The gearbox responds more decisively under acceleration.

Stronger low-end pull, The 2155 kg SUV feels lighter and more eager from a standstill.

Extended powerband, The factory power drop-off above 3700 RPM is smoothed out, giving the engine a stronger top-end pull.

Easier overtaking, Mid-range acceleration is noticeably improved, particularly valuable for a heavy 4WD vehicle.

Better towing capability, Extra low-end torque makes towing a 2500 kg trailer noticeably easier.

After Stage 1, the Tank 300 is ready for offroad equipment!

Stage 2 (Optional)


For customers seeking more, Stage 2 adds a downpipe and intake kit. This further reduces backpressure and allows a more aggressive calibration. Stage 2 delivers +39 WHP and +46 Nm over stock.

Remote Calibration Process

Step 1: Read the ECU
Use PCMFlash (Module 89), Kess3, DimSport, MagicMotorSport, or Combiloader. The Bosch MG1US008 supports OBD or Bench mode, depending on your programmer’s capability.

Step 2: Send the file
Upload the original file. We identify the software version, check for any stored fault codes, and build a custom calibration.

Step 3: Write the tuned file
We return the file within 1~2 hours. Writing takes under 10 minutes.

Step 4: Data logging and revisions
Drive for about 35 minutes. Log boost pressure, RPM, coolant temperature, intake air temperature, and transmission torque requests. Send the logs. We refine the file if needed. Usually 1~2 revisions are sufficient.

Safety and Transmission Considerations

The Stage 1 file stays within factory safety margins. We keep a backup of your original file. The calibration is 100% reversible. The ZF 8HP50 transmission torque limits are respected throughout. If writing is interrupted, professional tools have recovery modes. Every file is dyno-tested before delivery.

FAQ

How much gain does Stage 1 provide on the Tank 300 2.0T?
Stage 1 provides +20 WHP and +12 Nm at the wheels,(without boost increase in STG1) measured on our in-house DynoJet. From 178 WHP to 198 WHP, and from 349 Nm to 375 Nm.

Is the remap reversible?
Yes, 100%. CaracalTech keeps a backup of your original ECU file and can restore it at any time, for example before a dealer visit.

How long does the remote calibration process take?
The main process (reading, sending, writing) takes about 1–2 hours. Revisions, if needed, are completed within 1–2 days.

Will fuel consumption increase after the remap?
In many cases, fuel efficiency improves because the engine works more efficiently. Driving style remains the biggest factor.

What tools do I need for the Tank 300 remap?
You need PCMFlash (Module 89), Kess3, DimSport, MagicMotorSport, or Combiloader, a Windows laptop, and a stable internet connection.

Does this void the manufacturer's warranty?
The process is reversible. You can restore the original file before visiting a dealer for warranty service.

Can Pop & Bang be added to the Tank 300?
Yes. If the owner wishes, Pop & Bang can be calibrated and enabled as part of the remap. This feature is available on request.

Who is this for?
This Stage 1 remap is ideal for Tank 300 owners who want more low-end torque, sharper throttle response, and reduced transmission hesitation for daily driving and off-road use. It is not recommended for vehicles with existing timing chain wear or those using low-octane fuel without supporting modifications.

Is the Tank 300 engine the same as the Haval H9 engine?
No, they are not identical, although both come from the GWM engine family. The Haval H9 uses the GW4C20B, while the Tank 300 uses the E20CB. Both are 2.0-litre turbocharged units with a displacement of 1967~1978 cc, but the E20CB is the more advanced version. It features an electronically controlled twin-scroll turbocharger and meets Euro 6B emissions standards. The two engines share their core architecture, but the calibration strategy, turbo system, and emissions hardware are different. Our calibration files are developed specifically for each engine code, not shared between them.

For a detailed breakdown of the Haval H9 calibration strategy, see our dedicated Haval H9 ECU Remap article.

Does the Tank 300 require special maintenance after the remap?


Yes. A tuned engine benefits from more attentive maintenance, particularly in hot climates. We recommend the following:

Oil changes every 7,000~8,000 km using a high-quality fully synthetic oil (5W-30 API SP or equivalent). This is critical for the E20CB due to its known sensitivity to oil dilution.

Intake valve cleaning using a GDI-specific intake valve cleaner spray every 10,000~15,000 km. These solutions are sprayed into the intake tract while the engine runs and help dissolve carbon deposits on the back of the intake valves. This is a preventive measure, not a substitute for walnut blasting.

Walnut blasting every 40,000~60,000 km if carbon buildup is suspected. This physically removes deposits that chemical cleaners cannot fully eliminate.

Spark plug inspection every 20,000 km. Tuned engines place higher thermal loads on the ignition system.

Coolant level and condition checks at every oil change, especially in tropical and desert climates.

Use 95 RON fuel minimum. Lower-octane fuel increases the risk of knock and reduces the effectiveness of the calibration.

Why Choose CaracalTech?

  • Expert calibrators with experience on GWM engines
  • Remote service, no workshop visit required
  • Custom files, not generic maps
  • Revisions included
  • Dyno-verified results
  • Safe and reversible
  • Lifetime software warranty
  • Money-back guarantee
  • Free technical support

Ready to Unlock Your Tank 300?

Request a free quote. Book your remote tuning session. Ask us any questions.

Don’t let your Tank 300 run at factory settings. Unlock the extra 26 WHP and 26 Nm today.

Author: CaracalTech Calibration Team
Last Updated: September 2026

 

Keywords:bosch mg1us008 - e20cb chip tuning-tank 300 2.0t ecu remap-tank 300 dyno tuning-tank 300 stage 1 tuning-tank 300 stage 2-zf 8hp50 tuning

Enjoyed the content? Add us as a preferred source to see more of it in Search.

Add as a preferred source on Google
Your Rating
Rate: 5.00 (1)
Community
Comments: