whatsapp logo
ECU Remapping Course

ECM Titanium Training Course: Petrol ECU Remapping Online

Published Updated

Now playing: ECU Programming on the bench

498$4.0 (46)165 enrolled

ECM Titanium Training Course: Petrol ECU Remapping Online

Episodes
30
Time
10:44:13
Price
498$
Other Episodes

1 - What You Will Learn In This Course?

00:01:38

2 - Introduction of EFI system

00:22:14

3 - The types of ECUs

00:11:08

4 - What is ECU remapping and ECU cloning?

00:13:23

5 - Tools you need for Chiptuning and ECU remapping

00:20:46

6 - The types of programmers

00:24:53

7 - How to Read and Write ECU and Reflash

00:22:29

8 - ECU Programming on the bench

00:21:33

9 - Types of tuning software

00:18:38

10 - ECM Titanium software training

00:28:27

11 - ECM Titanium - Driver Maker Plugin

00:05:23

12 - Engine torque categories

00:41:46

13 - Air control category

00:39:33

14 - ignition timing and spark advance categories

00:37:49

15 - Injection system and Injection tables categories

00:46:08

16 - Turbo system categories

00:17:10

17 - Variable Valve Timing System (VVTI)

00:07:26

18 - Limiters

00:09:28

19 - How to modify the tables?

00:28:54

20 - Practical example (Audi A3 quattro 3.2 V6 Sport)

00:20:41

21 - Practical example (VW Beetle 2.0 TFSI)

00:29:54

22 - Practical example (TOYOTA LAND CRUISER PRADO with DENSO ECU)

00:17:49

23 - Audi S1-continental SIMOS(Understanding table)

00:33:46

24 - Audi S1-continental SIMOS(Modify table)

00:12:06

25 - AUDI TT example

00:36:08

26 - polaris_bosch me17 remap

00:09:49

27 - Polaris RZR Turbo

00:05:18

28 - Mini cooper Bosch MEVD17

00:18:10

29 - Description ECU table of Mercedes Benz C43 AMG with Bosch MED17.7.3 ? (part1)

00:23:42

30 - Description ECU table of Mercedes Benz C43 AMG with Bosch MED17.7.3 ? (part 2)

00:05:44

31 - How to modify ECU table of Mercedes Benz C43 AMG with Bosch MED17.7.3 ? (part 3)

00:13:58
lock icon

Log in to unlock this episode.

Information

ECU Programming on the bench

The steps we introduced earlier are the easiest ways to access the file. However, if the ECU file was not readable via an OBD-II and the file was not found in the Databank, we would need to find other solutions such as opening the ECU securing and using methods such as K-Line, Boot Loader, J-TAG, etc.

Usually, when the ECU is not readable via the OBD port, the software initially tells you the proper protocols, so that you will know whether to open the ECU or even the ECU as well from the vehicle.

To disconnect the ECU, you need to know where it is located. Most of the ECUs are placed under the dashboard or in the engine bay. Some companies tend to place the ECU in weird locations, therefore, if you didn’t know where it is located, you could look it up on the internet. After you found the ECU location, to disconnect the ECU from the vehicle, do the following steps.

  1. Before proceeding, make sure all electric consumers are turned OFF. 
  2. Turn the switch OFF and for safety reasons, place it far from the vehicle. Also
  3. and etc…

We generally have two protocols for reading the ECU “on the workbench” mode:

Programming using:

  1. Direct Connection to Pin Out of the Connector:

In this mode, it is not needed to open the ECU. Follow the guideline, connect the special wiring cables to ECU pins. Then preferably read the flash and EEPROM in Full backup mode. Be sure not to bend the connector pins. After reading the file, fully save it.

 

  1. Direct connection to the board:

In the second mode, you need to open the ECU and solder the wires using the J-TAG or Boot method.

You will learn how to open ECU case And how to reflash ECU with ktag programmer

Rate: 4.00 (46)

Enjoyed the content? Add us as a preferred source to see more of it in Search.

Add as a preferred source on Google
Community
Comments: