whatsapp logo
Dyno Project

OMODA 5 1.6TGDi Stage 1 ECU Remap, Dyno-Verified +25 WHP & +66 Nm

Published Updated
OMODA 5 1.6TGDi Stage 1 ECU Remap, Dyno-Verified +25 WHP & +66 Nm

OMODA 5 1.6TGDi Stage 1 ECU Remap: +25 WHP / +66 Nm (Dyno-Verified)

CaracalTech Stage 1 ECU remap for the OMODA 5 1.6TGDi (Chery SQRF4J16, 7-speed DCT) adds +25 WHP and +66 Nm at the wheels (approximately 13.5% power increase).

  • Measured on our in-house dynamometer.
  • The DCT torque limits are fully respected; the ECU and TCU remain synchronized.
  • The file is 100% reversible, with a lifetime software warranty and money-back guarantee.
  • Remote calibration with data-log revisions, typically within 1~2 hours.

Engine & Factory Output

The OMODA 5 1.6TGDi is powered by the SQRF4J16 (F4J16), a 1.6-litre turbocharged petrol engine from Chery Automobile. This engine is shared across several Chery group platforms, including the Tiggo 8 Pro, Exeed TXL, Exeed VX, and Jetour X70 Plus. In the OMODA 5, it is factory-rated at 197 HP and 275 Nm.

Key Specifications:

Specification

Value

Engine Code

SQRF4J16 (F4J16)

Displacement

1598 cc

Max Power (Factory)

197 HP

Max Torque (Factory)

275 Nm @ 2000–4000 RPM

Transmission

7-speed DCT (front-wheel drive)

Compression Ratio

9.9:1

Weight

1430 kg

ECU

Bosch MED17.8.10 (TC1728 processor)

Fuel Requirement

95 RON minimum

The OMODA 5 is sold under different names in different markets. In Russia and Europe, it is marketed as the Omoda C5. In China, it was originally the Chery Omoda 5. Regardless of the badge, the hardware and calibration architecture are identical.

Stage 1 Calibration Strategy for the SQRF4J16

Stage 1 is a software-only modification. No hardware changes are required. On this engine, we focus on five key areas:

Torque management for the 7-speed DCT: The DCT has specific torque limits. We recalibrate the engine torque model to stay within safe clutch and gearbox parameters while maximizing usable output.

Ignition timing under 9.9:1 compression: This compression ratio is relatively high for a turbocharged engine. We advance timing carefully within the knock threshold, using factory knock sensor feedback to validate safety.

Turbo boost pressure: We increase boost within the turbocharger’s efficiency range, focusing on low-to-mid RPM response rather than chasing peak numbers.

Cooling system calibration for tropical climates: Because the SQRF4J16 is turbocharged, we adjust cooling system parameters to reduce operating temperatures in hot climates, protecting the engine under sustained high-load conditions.

Conservative ignition advance: We carefully select ignition advance changes to prevent knock, especially in high ambient temperatures and with varying fuel quality.

All adjustments stay within factory safety margins. The original file is always backed up.

Pre-Calibration Health Check

Before any remap, we recommend inspecting the following known weak points of the SQRF4J16:

Timing chain – Reports of chain stretch at 25,000–60,000 km. If chain wear is present, calibration is postponed until replacement.

Oil level and quality – The engine is prone to oil consumption. Fresh, high-quality oil is essential before tuning.

Intake valve deposits – GDI engines accumulate carbon on intake valves. If deposits are suspected, a walnut blasting service is recommended.

Water pump – The factory water pump has a known failure rate. We inspect the cooling system before tuning, especially in hot climates.

Known Weaknesses of the SQRF4J16 (and How Our Calibration Addresses Them)

The SQRF4J16 is a robust engine, but it has several known weak points that must be considered during calibration:

 

WeaknessDetailsOur Approach

Timing chain stretch

Reports of chain stretch at 25,000–60,000 km; some cases of chain failure-1We inspect the timing chain before any remap. If wear is present, calibration is postponed until replacement.

Oil consumption and dilution

The engine is prone to oil consumption and GDI can cause fuel dilution in the crankcase.Our calibration avoids aggressive post-injection strategies that worsen dilution.

Intake valve deposits

GDI engines are susceptible to carbon buildup on intake valves.We recommend a walnut blasting service before calibration if deposits are suspected.

Water pump failure

The factory water pump has a high failure rate, often after warranty-2We inspect the cooling system before tuning, especially in hot climates.

High compression ratio (9.9:1)

Limits safe ignition advance; higher knock risk.We use conservative timing maps and rely on knock sensor feedback for validation.

Fuel quality sensitivity

The engine requires 95 RON minimum; low-octane fuel can cause knock-3In regions with low-octane fuel, we adjust the calibration to operate safely within available fuel quality.

 

OMODA 5 Stage 1 Case Study, Dyno-Verified Results

Our in-house dyno testing on the OMODA 5 1.6TGDi produced the following results at the wheels:

OMODA 5 1.6TGDi Stage 1 ECU Remap, Dyno-Verified +25 WHP & +66 Nm
VersionPower (WHP)Torque (Nm)
Stock185284
Stage 1210350
Stage 2 (Downpipe + Intake Kit)225375

Stage 1 delivers +25 WHP and +66 Nm at the wheels. That is a 13.5% power increase and a 23% torque increase—without any hardware changes.

Test Conditions: In-house dynamometer, ambient temperature 28–32 °C, 95 RON fuel, vehicle mileage under 30,000 km.

The torque gain is particularly strong in the low-to-mid range (2000–4000 RPM), which is exactly where the OMODA 5 needs it most for daily driving.

Stage 2 (Optional)
For customers seeking more, Stage 2 adds a downpipe and intake kit. This further reduces backpressure and allows a more aggressive calibration. Stage 2 delivers +40 WHP and +91 Nm over stock. Recommended for off-road or track use only.

How It Feels on the Road

The extra torque transforms the OMODA 5’s character:

Sharper throttle response: The electronic lag between pedal and engine is significantly reduced.

Stronger low-end pull: The car feels lighter and more eager from a standstill.

Quicker DCT shifts: The gearbox sees stronger torque signals and responds more decisively.

Easier overtaking: Mid-range acceleration is noticeably improved.

Better highway merging: The car no longer feels out of breath when joining fast traffic.

The OMODA 5 does not feel like a different vehicle after Stage 1. It feels like the factory restriction has been removed and the engine finally has room to breathe.

Remote Calibration Process

Step 1 – Read the ECU
Use ECU Tuning Tools named in Below to Read The ECU Bosch MED17.8.10 The reading process is non-invasive and carries no risk.

 ProgrammerReading Process
1KESS 3Bench mode
2Dim SportBench Mode
3Magic Motor SportOBD
4PCM FlashOBD
5CombiloaderOBD

 

Step 2: Send the file
Upload the original file. We identify the software version, check for any stored fault codes, and build a custom calibration.

Step 3: Write the tuned file
We return the file within 1~2 hours. Writing takes under 10 minutes.

Step 4: Data logging and revisions
Drive for about 35 minutes. Log boost pressure, RPM, coolant temperature, and DCT torque requests. Send the logs. We refine the file if needed. Usually 1–2 revisions are sufficient.

Safety and DCT Considerations

The Stage 1 file stays within factory safety margins. We keep a backup of your original file. The calibration is 100% reversible. The DCT torque limits are respected throughout. If writing is interrupted, professional tools have recovery modes. Every file is dyno-tested before delivery.

FAQ

How much gain does Stage 1 provide on the OMODA 5 1.6TGDi?
Stage 1 provides +25 WHP and +66 Nm at the wheels, measured on our in-house dynamometer. From 185 WHP to 210 WHP, and from 284 Nm to 350 Nm.

Is the remap reversible?
Yes, 100%. CaracalTech keeps a backup of your original ECU file and can restore it at any time, for example before a dealer visit.

How long does the remote calibration process take?
The main process (reading, sending, writing) takes about 1~2 hours. Revisions, if needed, are completed within 1–2 days.

Will fuel consumption increase after the remap?
In many cases, fuel efficiency improves because the engine works more efficiently. Driving style remains the biggest factor.

What tools do I need for the OMODA 5 remap?
Yes, You need: 
(1) Programmer to reading the ECU Bosch MED17 or MG1 (maybe)
(2)  laptop with healthy battery
(3) A stable internet connection.
 We can guide you on purchasing the right device

Does this void the manufacturer's warranty?
The process is reversible. You can restore the original file before visiting a dealer for warranty service.

Who is this for?
This Stage 1 remap is ideal for OMODA 5 owners who want more low-end torque for daily driving. It is not recommended for vehicles with existing timing chain wear, DCT clutch wear, or those using low-octane fuel without supporting modifications.

Why Choose CaracalTech?

  • Expert calibrators with experience on Chery group engines
  • Remote service, no workshop visit required
  • Custom files, not generic maps
  • Revisions included
  • Dyno-verified on our in-house dynamometer
  • Safe and reversible
  • Lifetime software warranty
  • Money-back guarantee
  • Free technical support

Ready to Unlock Your OMODA 5?

Request a free quote. Book your remote tuning session. Ask us any questions.

Don’t let your OMODA 5 run at factory settings. 

📍For more information and probable problems feel free to contact us: [email protected]

 

Author: CaracalTech Calibration Team
Last Updated: September 2026

Keywords:bosch med17.8.10-chery omoda 5 tuning-fownix fx chip tuning-omoda 5 1.6t ecu remap-omoda c5 stage 1 tuning-sqrf4j16

Enjoyed the content? Add us as a preferred source to see more of it in Search.

Add as a preferred source on Google
Your Rating
Rate: 5.00 (1)
Community
Comments: