whatsapp logo
Dyno Project

GAC Empow 2.0T Stage 1 & Stage 2 ECU Remap +21 WHP / +31 Nm (DynoJet-Verified)

Published Updated
GAC Empow 2.0T Stage 1 & Stage 2 ECU Remap +21 WHP / +31 Nm (DynoJet-Verified)

GAC Empow 2.0T Stage 1 & Stage 2 ECU Remap, +21 WHP / +31 Nm (DynoJet-Verified)

Fast View:

  • CaracalTech Stage 1 ECU remap for the GAC Empow 2.0T (4B20J1, 7-speed DCT) adds +21 WHP and +31 Nm at the wheels.
  • Stage 2 (Downpipe + Intake Kit) pushes further to +35 WHP and +57 Nm over stock.
  • Measured on our in-house DynoJet dynamometer in Dubai.
  • The DCT shift logic is recalibrated to reduce the factory hesitation; the 7WF25G torque limits are fully respected.
  • Cooling system parameters are adjusted to lower operating temperatures in hot climates.
  • The file is 100% reversible, with a lifetime software warranty and money-back guarantee.
  • Remote calibration with data-log revisions, typically within 1~2 hours.

Engine & Factory Output

The GAC Empow 2.0T is powered by the 4B20J1, a 2.0-litre turbocharged petrol engine from GAC Motor. This engine is shared across several GAC group platforms, including the Emkoo, GS4 Plus, GA8, and M8. In the Empow, it is factory-rated at 239 HP and 385 Nm.

Key Specifications:

SpecificationValue
Engine Code4B20J1
Displacement1961 cc
Max Power (Factory)239 HP @ 5250 RPM
Max Torque (Factory)385 Nm @ 1750~4000 RPM
Transmission7-speed DCT (7WF25G, wet clutch, front-wheel drive)
Compression Ratio10.5:1
Weight1440 kg
Fuel Tank Capacity55 L
ECUBosch MG1UA008
Fuel Requirement95 RON minimum

The GAC Empow is also sold as the Trumpchi Empow in China and the GAC Shadow Leopard in some export markets. Regardless of the badge, the hardware and calibration architecture are identical.

Stage 1 Calibration Strategy for the 4B20J1

Stage 1 is a software-only modification. No hardware changes are required. On this engine, we focus on four key areas:

Torque management and shift logic for the 7-speed DCT: The factory 7WF25G transmission exhibits noticeable hesitation during gear changes across all driving modes. We recalibrate the engine torque model and the DCT torque request strategy to reduce this delay while staying within safe clutch and gearbox parameters.

Ignition timing under 10.5:1 compression: This compression ratio is moderate for a turbocharged engine. We advance timing carefully within the knock threshold, using factory knock sensor feedback to validate safety.

Turbo boost pressure: We increase boost within the turbocharger's efficiency range, focusing on low-to-mid RPM response rather than chasing peak numbers.

Throttle mapping: We reduce electronic throttle lag for sharper pedal response.

All adjustments stay within factory safety margins. The original file is always backed up.

Thermal and Mechanical Considerations for Hot Climates

The 4B20J1 is a direct-injection turbocharged engine with documented sensitivity to thermal load. In hot climates, several factors require attention before calibration:

Cooling system calibration for hot climates: We adjust cooling system parameters to reduce operating temperatures, protecting the engine and turbocharger under sustained high-load conditions. This is particularly important in tropical and desert climates where ambient temperatures regularly exceed 40 °C.

Turbocharger heat management: The factory manual explicitly requires the engine to idle for a period before shutdown to gradually lower turbocharger operating temperature and prevent oil carbonization in the bearing housing. Our calibration includes thermal management strategies that reduce peak turbo temperatures during hard driving, complementing this factory requirement.

Fuel quality sensitivity: The 4B20J1 requires 95 RON minimum. In regions with lower-octane fuel, we adjust the calibration to operate safely within the available fuel's knock resistance.

Intake valve carbon deposits: GDI engines accumulate carbon on intake valves, which increases knock tendency. A walnut blasting service is recommended if deposits are suspected.

Case Study: Dyno-Verified Stage 1 & Stage 2 Results

Our in-house DynoJet testing on the GAC Empow 2.0T produced the following results at the wheels:

GAC Empow 2.0T Stage 1 & Stage 2 ECU Remap +21 WHP / +31 Nm (DynoJet-Verified)
VersionPower (WHP)Torque (Nm)
Stock (Run 0)216 WHP @ 5100 RPM346 Nm @ 2900 RPM
Stage 1 (Run 1)237 WHP @ 5000 RPM377 Nm @ 3000 RPM
Stage 2 (Downpipe + Intake Kit, Run 2)251 WHP @ 5150 RPM403 Nm @ 2950 RPM

Stage 1 delivers +21 WHP and +31 Nm at the wheels. Stage 2 pushes further to +35 WHP and +57 Nm over stock.

Test Conditions: In-house DynoJet dynamometer, ambient temperature 35~40 °C, 95 RON fuel, vehicle mileage approximately 23,000 km.

Important Note on Data Interpretation: You may see different gain figures for the GAC Empow 2.0T on international tuning forums. For example, MasterTuning (Europe) reports Stage 1 gains of approximately 10% for the 265 HP variant. These differences come from three factors: different testing standards (wheel vs. engine output), different tuning aggressiveness (safety margin vs. maximum output), and different factory calibration versions (239 HP vs. 265 HP). Our calibration strategy prioritizes reliability and daily drivability, delivering verified, repeatable gains within safe margins.

For Stage 2, the decat procedure is applied automatically. This disables the downstream O2 sensor and suppresses the catalyst efficiency DTC (P0420).

How It Feels on the Road

The extra torque transforms the Empow's character:

Sharper throttle response: The electronic lag between pedal and engine is significantly reduced.

Smother DCT shifts: The factory hesitation during gear changes is noticeably diminished. The gearbox responds more decisively under acceleration.

Stronger low-end pull: The car feels lighter and more eager from a standstill.

Easier overtaking: Mid-range acceleration (3000~5000 RPM) is noticeably improved.

Better highway merging: The car no longer feels out of breath when joining fast traffic.

After Stage 1, the Empow Will be Driven Faster and Smarter!

Stage 2 (Optional)


For customers seeking more, Stage 2 adds a downpipe and intake kit. This further reduces backpressure and allows a more aggressive calibration. Stage 2 delivers +35 WHP and +57 Nm over stock. The  Decat procedure is applied automatically for Stage 2, disabling the downstream O2 sensor and suppressing the catalyst efficiency error code (P0420).

Remote Calibration Process

Step 1: Read the ECU
Use Proper ECU Tuning tools named in Below to Read The ECU Bosch MG1UA008. The reading process is non-invasive and carries no risk.

 ProgrammerReading Process
1KESS 3Bench mode
2Dim SportBench Mode
3Magic Motor SportOBD
4PCM FlashOBD
5CombiloaderOBD

Step 2: Send the file
Upload the original file. We identify the software version, check for any stored fault codes, and build a custom calibration.

Step 3: Write the tuned file
We return the file within 1~2 hours. Writing takes under 10 minutes.

Step 4: Data logging and revisions
Drive for about 35 minutes. Log boost pressure, RPM, coolant temperature, intake air temperature, and DCT torque requests. Send the logs. We refine the file if needed. Usually 1~2 revisions are sufficient.

Safety and Transmission Considerations

The Stage 1 file stays within factory safety margins. We keep a backup of your original file. The calibration is 100% reversible. The 7WF25G transmission torque limits are respected throughout. If writing is interrupted, professional tools have recovery modes. Every file is dyno-tested before delivery.

FAQ

How much gain does Stage 1 provide on the GAC Empow 2.0T?
Stage 1 provides +21 WHP and +31 Nm at the wheels, measured on our in-house DynoJet. From 216 WHP to 237 WHP, and from 346 Nm to 377 Nm.

Is the remap reversible?
Yes, 100%. CaracalTech keeps a backup of your original ECU file and can restore it at any time, for example before a dealer visit.

How long does the remote calibration process take?
The main process (reading, sending, writing) takes about 1~2 hours. Revisions, if needed, are completed within 1~2 days.

Will fuel consumption increase after the remap?
In many cases, fuel efficiency improves because the engine works more efficiently. Driving style remains the biggest factor.

What tools do I need for the GAC Empow remap?
You need: 
(1) Programmer to reading the ECU Bosch MG1UA008
(2)  laptop with healthy battery
(3) A stable internet connection.
 We can guide you on purchasing the right device.

Does this void the manufacturer's warranty?
The process is reversible. You can restore the original file before visiting a dealer for warranty service.

Can Pop & Bang be added to the GAC Empow?
Yes. If the owner wishes, Pop & Bang can be calibrated and enabled as part of the remap. This feature is available on request and can be fine-tuned for intensity. Note: The Catalyst should be removed.

Who is this for?
This Stage 1 remap is ideal for Empow owners who want more low-end torque, sharper throttle response, and reduced DCT shift hesitation for daily driving. It is not recommended for vehicles with existing transmission issues or those using low-octane fuel without supporting modifications.

Why Choose CaracalTech?

  • Expert calibrators with experience on GAC group engines
  • Remote service, no workshop visit required 
  • Custom files, not generic maps
  • Revisions included
  • Dyno-verified on our in-house DynoJet
  • Safe and reversible
  • Lifetime software warranty
  • Money-back guarantee
  • Free technical support

Ready to Upgrade Your GAC Empow?

Request a free quote. Book your remote tuning session. Ask us any questions.

Don't let your GAC Empow run at factory settings. Unlock the extra 21 WHP and 31 Nm today.

📍For more information and probable problems feel free to contact us: [email protected]

Author: CaracalTech Calibration Team
Last Updated: September 2026

Keywords:4b20j1 chip tuning-bosch mg1ua008-gac empow 2.0t ecu remap-gac empow dyno tuning-gac empow stage 1 tuning-gac empow stage 2-trumpchi empow tuning

Enjoyed the content? Add us as a preferred source to see more of it in Search.

Add as a preferred source on Google
Your Rating
Rate: 5.00 (1)
Community
Comments: