whatsapp logo
ECU Remapping Course

Bosch ME17.8.8 ECU Tuning Course in WinOLS (Chinese Cars)

Published Updated
70$4.5 (6)108 enrolled

Bosch ME17.8.8 ECU Tuning Course in WinOLS (Chinese Cars)

Episodes
1
Time
00:14:02
Price
70$
Information

What You Will Learn In This Course?

Quick answer: This is a short WinOLS video course on remapping Bosch ME17 petrol ECUs, mainly the ME17.8.8, in Chinese cars such as Chery, Changan, Haima and Besturn models. In two videos, a 2-minute introduction and a 14-minute main lesson, you learn where six key maps sit in the file, what each one does and how to change it: lambda for component protection, requested lambda, optimal engine torque, requested engine load, spark advance and the driver torque request. The price shown on this page is 70$.

🚩This Video Teaches You How to Remap Bosch ME17's ECUs Installed in Chinese Automobiles in The WinOLS ECU Tuning Software.

Chinese cars like Chery Tiggo 5, Haima S7 Turbo, Changan CS35, Chery Arrizo 5, Besturn B30, and many other Chinese-made automobiles use the Bosch ME17 series of ECUs.

Four Chinese-made cars of the kind that use a Bosch ME17 ECU
 Bosch ME17's ECUs installed in Chinese automobiles

💬Chinese cars are equipped with two makes of the Bosch ME17 ECU: one with a metal frame and the other with a plastic frame.

The photos further down this page show both versions: one with a metal housing and one with a black plastic housing.

You can read and write this ECU with tools such as CombiLoader or ChipLoader, or with Alientech K-TAG. Check your tool's ECU list for your exact ME17 version before you start. Disclosure: CaracalTech sells Alientech products, such as KESS3 and ECM Titanium.

If you carefully watch the video and learn the tips, you can remap the mentioned automobiles and other cars with the Bosch ME17 ECU.

Reading a Bosch ME17 ECU in a Chinese car with a laptop, a programming tool and its software
Programming & ECU Tuning of Chery

💬We Explain The Tables Below in This Video:

Bosch ME17 ECU made in China with a metal housing
Bosch ME17.8.8 ECU
  1. Lambda for component protection
  2. Requested lambda
  3. Optimal engine torque
  4. Requested engine load
  5. Spark advance
  6. Torque request by the driver 
Bosch ME17 ECU made in China with a black plastic housing
Bosch ME17.8.8 ecu 

In this video, we explain how you can find these tables, what they are, and how to modify them. The modifications you learn in this training video are based on remapping cars like Haima S7 Turbo and the Chery Tiggo 7, tested on a chassis dynamometer at CaracalTech. You can see examples of our dyno work in the projects section.

🏁The course has two videos: a 2-minute introduction and a 14-minute main lesson, about 16 minutes in total.

Course facts

ItemDetail
FormatOnline video course, 2 videos
Length2 min 1 s introduction + 14 min 2 s main lesson
ECUBosch ME17, mainly ME17.8.8, in Chinese cars
Software usedWinOLS (EVC electronic)
Maps covered6: component-protection lambda, requested lambda, optimal engine torque, requested engine load, spark advance, driver torque request
Price70$, as shown on this page

Who this course is for

Tuners and workshops that remap Chinese petrol cars with a Bosch ME17 ECU and already know the basics of WinOLS. If you are new to WinOLS, start with our WinOLS training course for petrol engines. If you work in ECM Titanium, see the ECM Titanium petrol course.

What you need

  • WinOLS from EVC. To practise, you can use the free official demo; it cannot export a modified file. Read more in our guide to WinOLS 5 price and demo.
  • A tool that can read and write your ME17 version, and an original, complete read of the ECU.
  • Basic knowledge of petrol maps helps. Our articles on AFR and lambda and on the spark advance table explain two of the six maps.
  • Optional: a ready-made WinOLS mappack, if one exists for your ECU, saves map-finding time.

Bosch ME17 course: frequently asked questions

What is a Bosch ME17 ECU?

Bosch ME17 is a family of petrol engine ECUs from the same generation as the Bosch MED17 and the diesel EDC17. Its maps sit in the internal flash memory of an Infineon TriCore microcontroller, while the EEPROM holds immobiliser and adaptation data, not maps (Master-Ecu). This course works with the ME17.8.8 found in many Chinese cars.

Which cars use the Bosch ME17.8.8?

In this course we work with Chinese petrol cars such as the Chery Tiggo 5, Chery Tiggo 7, Chery Arrizo 5, Haima S7 Turbo, Changan CS35 and Besturn B30. Other Chinese brands also use ME17 versions. Always check the label on the ECU and the software version in the file before you choose a map definition.

Can I use the same steps on a Ford or Chevrolet ME17?

The map names and the logic, such as requested lambda, optimal torque and requested load, are similar across ME17 versions. The addresses, axes and values are not the same, so you must find the maps again in each file. The examples in the video come from Chinese ME17.8.8 files.

Which file do I need to read from the ME17?

The complete internal flash, without any conversion. If you read on the bench, also keep a backup of all memories. The EEPROM alone is not enough, because it holds no maps (Master-Ecu).

Does the course cover IMMO off or DTC off?

No. The course covers the six performance maps listed above. If you need these functions, see our IMMO off solution and DTC off solution, or upload your file in our tuning file service.

📍For more information and probable problems feel free to contact us: [email protected]

Usage note: IMMO off is supplied only for ECU repair or replacement work on the owner's own vehicle. DTC off on emissions-related parts is supplied for off-road machinery and motorsport vehicles only, where local regulations permit; it is not intended for vehicles used on public roads.

Rate: 4.50 (6)

Enjoyed the content? Add us as a preferred source to see more of it in Search.

Add as a preferred source on Google
Community
Comments:
OSCAR(May 31st 2023)
ME17 series learning
Do you have more training courses for this type of ECUS? I would like to learn Immo of and DTC removing also!! If I take this course could you help me to CHIPTUNING my 2020 Chevrolet sail 1.5 whit ME17 ecu?
OSCAR(June 2nd 2023)
ME17 Chevrolet Sail
Could you teach me how make DTC clearing of this ecu if I take this course? Best regards!
Vagner(July 27th 2023)
Focus 2.0 16v me17
Guys can use same procedure for this vehicle? Another point hiw can I read bosch for Ford Territory? Tks!
Vagner(July 27th 2023)
Ford Territory read pcm bosch
Hi guys how can I read PCM ford territory? Please can send the instructions? Thanks!
Vagner(July 27th 2023)
Bosch med17
If I replace the throttle body or exhaust in this case do I need change the optimal torque and request engine load or just Requested lambda?
Vagner(July 29th 2023)
Throttle body or exhaust replace
Guys after replace throttle body or exhaust in this case do we have change lambda requested or optimal torque or requested engine load?
Vagner(July 31st 2023)
Optmal torque and engine load
Can I use same value for optmal torque and engine load in other Bosch Me17? For exemple Fors Focus Me17 flex fuel 2.0 16v. Thanks!
Vagner(August 21st 2023)
Optmal torque X requested engine load
Hi guys! what is the difference between the maps and when should i change the optmal torque or the requested engine load?
Vagner(September 2nd 2023)
Focus ME17.8.5 2.0 16V DTC's after replace the throttle.
Hi guys! I watch the vídeos and change the maps from module following the vídeos. I replaced my throttle body 55mm for 57mm now I ahe two DTC's set: P2108 P0638 Please how can I fix the issue? In this case what maps should I change? Thanks!
Vagner(January 14th 2024)
Drive wish when is need?
How can I know is need increase drive wish and optmal torque?