Toyota Fortuner 2013 Remapping

Toyota Fortuner 2013 Remapping:

Introduction:

Our desired car in this article is Toyota Fortuner 2013, the second Facelift Of first generation was marketed from 2012 to 2015. The Toyota Fortuner is a medium-sized SUV based on the famous Toyota product Hilux.
The Fortuner has a double-wishbone front suspension and a leaf spring type rear axle, like other pickups, which provides an adequate ride quality and no irritating shocks in this class of vehicle on bad roads. 
The most important competitors of Fortuner are Chevrolet Trailblazer, Mitsubishi Pajero Sport and Nissan pathfinder.

Advantages:

• High performance & reliable powertrain
• Distinct style
• High off-road capabilities 
• Acceptable on-road and off-road ride quality 

Disadvantages:

• Drum brakes at rear wheels
• Excessive pedal delay results in a loss of power and torque at start-up
• In 4-cylinder petrol vehicles, there is a lack of power that has to be reinforced
• No ventilated seats
• Stiff suspension, not good for daily usage
• Difficult access to 3rd row seats

Petrol:

• 2700 cc  (160 hp) 2TR-FE  VVT-I I4                              (EMS: Denso 175822-887)
• 4000 cc (224 hp) 1GR-FE  VVT-I V6                            (EMS: Denso 275136-2010)
• 4000 cc (302 hp) 1GR-FE  VVT-I V6 TRD EDITION    (EMS: Denso 275036-0360)

Diesel:

• 2500cc 144 hp / 2KD-FTV D-4D Turbodiesel I4         (EMS: Denso 275922-022)
• 3000cc 169 hp / 1KD-FTV D-4D Turbocharged I4      (EMS: Denso 175822-887)

Appropriate Programmers for Fortuner Remap:

• ALIENTECH

Kess3, an Alientech Co.’s device, can be used to download VR through OBD. In this case, you should first study the ECU specs, then download the original file from the databank site, and finally, remap using the ECM Titanium software. Then, when you have corrected Checksum, go ahead and write. You should use the 517 OBD protocol to download all of the engines specified for the 2nd facelift of first generation of Fortuner. Note that this programmer cannot read the ECU file, so choose the Original file carefully.

🚨NOTE: For downloading Toyota Fortuner file with 1GR engine, you need to choose Toyota FJ Cruiser in menu.

• BIT BOX

One of the most powerful programmers for remapping Toyota Company products is the Beatbox programmer. For the engines described above, the Can GEN1 module should be included in this programmer. In addition, for the 1TR engine, a NewGEN can be given. The bit edit supplement program allows you to remap the relevant tables.

✅The following are the benefits of the CaracalTech Remap package:

• Boosting acceleration and power by up to 15% in petrol vehicles and 25% in diesel ones.
• Improved accurate air to fuel ratio adjustment for more torque at low revs
• Speed limiter Removal
• Significant improvement in the responsiveness of the accelerator pedal (linearization of throttle behavior without the need for further devices such as a pedal box)
• In petrol models, the DeCat error has been eliminated.
• In petrol models, the second oxygen sensor has been removed.
• In diesel engines, EGR Off and DPF Off  will be done.
• Fixing the problem with the AdBlue repository
• Raising the cutoff point for the number of client requests (Rev Limit removal)
• Removing immobilizer; IMMO Off
• Supercharger packages are supported.
• Watermethanol injection packages are supported.

Contact us via one of the following three ways, to use our experiences in Toyota Fortuner remapping and access to all parameters without any error.  

1- If you want to learn how to remap Toyota Fortuner with DENSO ECU in WinOLS and ECM Titanium Software, you can enter to our ECU training course.

2- If you need only remapping file, upload original ECU file in Tuning File Service, after short time our experts send you remapped file.

3- If you know remapping software like WinOLS or ECM Titanium, for ease and accuracy of work you can use CaracalTech's Mappacks in the following link.

📍For more information and probable problems feel free to contact us: support@caracaltech.com